
36" x 36" Barrier Free Shower Pan, Roll In Shower Pan
Transfer-shower proportions.
The pan decides the footprint, the drain location and how low the entry can be. Pick it after you measure, because once it is set in mortar everything else is built around it.
Every roll-in pan comes down to four choices: footprint (width × depth), drain (center, end, or trench), entry (flush, beveled low threshold, or a collapsible dam), and shape (rectangular alcove, corner, or neo-angle). The 15 pans linked from this site run from 36 × 36 inches up to 60-inch-long models, with center, trench and dual-option drains.
The building code minimum and the stall sizes most homes already have are laid out in our standard shower size chart; the table below covers pans built for low or flush entries.
| Nominal footprint | How it is often used | Roll-in notes |
|---|---|---|
| 36 × 36 to 42 × 42 | Replacing a small stall shower; transfer-style use | Too short for the 60-inch ADA roll-in reference; works for transfers to a seat |
| 48 × 34 to 48 × 48 | Converting a closet or small stall; corner showers | A 30 × 48 wheelchair space can fit in a 48 × 48 on paper, but turning inside is not possible |
| 51 × 39 to 54 × 36 | Shorter tub alcoves and mid-size remodels | Shorter than a typical 60-inch alcove; check the leftover space at the end |
| 60 × 29 to 60 × 36 | Direct tub replacement in a 60-inch alcove | Matches the length of the ADA standard roll-in reference; confirm the clear inside depth |
| 60 × 48 and larger | Primary-bath remodels; caregiver-assisted bathing | Extra depth gives a helper room beside the user |
Nominal sizes are outside dimensions as named by the seller. The clear inside space is smaller once flanges and walls are in place. Always ask for the specification drawing.
Replacing a tub? Check the drain size rules for tub-to-shower conversions before you pick an outlet.
A center drain sits in the middle of the pan and the floor slopes to it from all sides. It is the most common molded-pan layout. An end drain sits near one short side, which can line up with an old tub drain. A trench drain is a long channel along one edge, so the floor slopes in one plane. Two pans linked here list a trench drain, and one of those also offers a center-drain option.
The most practical rule: choose the pan whose drain lands closest to where your existing drain already is. Moving a drain under a wood floor is common; under a slab it means cutting concrete.
Pans called "barrier-free" or "roll-in" usually have a beveled low threshold or a flush entry designed to sit level with the finished floor. Some listings describe a low threshold without giving a height. For wheelchair use, ask the seller for the actual entry height and bevel and compare it to the user's chair. The ADA reference for a roll-in is ½ inch maximum. A pan described as "step in" may have a higher lip that suits walkers but not wheels.
Corner pans have two finished sides and two wall sides, which can open up a bathroom and give a wider approach. Neo-angle pans clip the front corner at an angle, so the entry faces diagonally. That can make a small room feel bigger, but a diagonal entry is narrower than the pan width and harder to roll into straight. Measure the entry face itself.
Most molded pans need full support underneath, usually a mortar bed or the manufacturer's specified setting compound, on a flat, solid subfloor. Gaps under the pan cause flexing, cracking and leaks at the drain. The installer should dry-fit the pan, check the drain alignment, check level in both directions, and follow the manufacturer's sequence for connecting the drain and sealing the flanges. Ask for photos before the walls go on.
The pans on this site link to their listings at Showers4Less, where current price, specification sheets and stock are shown. Each pan also has a planning page here that compares its nominal size with the ADA reference sizes. Verify the live listing before ordering.
Open a pan for its size comparison, drain and entry notes. Each planning page links to the live store listing.

Transfer-shower proportions.

Compact; better for transfers or seated use than rolling in.

Compact; better for transfers or seated use than rolling in.

Compact; better for transfers or seated use than rolling in.

Compact; better for transfers or seated use than rolling in.

Drain: trench (linear). Holds a 30 × 48 wheelchair space on paper; shorter than a 60-in. roll-in.

Holds a 30 × 48 wheelchair space on paper; shorter than a 60-in. roll-in.

Drain: trench or center (listed as an option). Holds a 30 × 48 wheelchair space on paper; shorter than a 60-in. roll-in.

Drain: center. Holds a 30 × 48 wheelchair space on paper; shorter than a 60-in. roll-in.

Drain: center. Holds a 30 × 48 wheelchair space on paper; shorter than a 60-in. roll-in.

Holds a 30 × 48 wheelchair space on paper; shorter than a 60-in. roll-in.

Holds a 30 × 48 wheelchair space on paper; shorter than a 60-in. roll-in.

Holds a 30 × 48 wheelchair space on paper; shorter than a 60-in. roll-in.

Drain: center. Reaches the 30 × 60 roll-in reference footprint on paper.

Compact; better for transfers or seated use than rolling in.
Official sources come first. Cost figures come from consumer cost surveys and are planning ranges, not quotes. Rules and dollar limits change, so check the live page before you rely on a number.
Last checked 2026-10-10.
Start with the opening and the user. To replace a tub, most people look at 60-inch pans in 30- to 36-inch depths. For wheelchair users who stay seated, the 30 × 60-inch ADA reference is a common minimum for the clear inside space.
Either can work. A center drain is typical in molded pans. A trench drain allows a one-direction slope and a level entry edge. Choose the one that lines up with your drain and floor.
Yes, if the slab is flat and the drain is in the right place. For a flush entry the slab may have to be lowered in the shower area.
It varies by model. Ask the seller for the actual entry height and bevel. The ADA reference for a roll-in is ½ inch maximum.
Share the basic room and user needs. Aging Safely Baths can discuss product and installation paths. Submitting the form does not guarantee service availability, funding, product fit, price, or project timing.
1-888-779-2284